BMW M3 Forum
BMW M3 Forum BMW M3 Gallery BMW M3 Reviews BMW M3 Social Groups BMW M3 Chat M3Forum Sponsors >>
Loading


Mobile M3forum
Go Back   BMW M3 Forum.com (E30 M3 | E36 M3 | E46 M3 | E92 M3 | F80/X) > M3Forum Garage > Faults, Fixes and DIY
Tire Rack Buy Winter Tires Now!
Not a member? Register Now!
Register Gallery All Albums Garage Search Today's Posts Mark Forums Read Calendar FAQ

Faults, Fixes and DIY Please share your experience and knowledge with other members by contributing your own DIY, or by helping another member find the elusive fix!


Reply
 
Thread Tools Display Modes
Old Wed, Feb-28-2007, 02:24:08 AM   #1
lax01
Registered User
 
lax01's Avatar
 
Join Date: Feb 2006
Age: 33
Posts: 2,719
Reputation: 0 lax01 will become famous soon enough
Location: Los Angeles, CA

United States




Default DIY: E46 M3 Spark-Plugs with Pictures

Disclaimer: This is merely a reference, please do not attempt if you are not comfortable with doing work on your car

Car: 2002 BMW M3 (Build Date 11/01)

Parts Needed:

6 x Spark Plugs (I used Denso Iridium IXU24 5309 purchased from Sparkplugs.com)



Tools Needed:

Torx T30 (pictured above) - used to remove Micro-filter holder, definitely needed
Torque Wrench
5/8 Spark-Plug socket
1/4 Drive Ratchet
3/8 Drive Ratchet
10mm socket
1 or 2 3/8 drive extension (12" is probably not enough)

As this is the first time I attempted any DIY work on my car, I took a good mental picture of what the engine bay look like; this will hopefully prevent any confusion later. You can also take a photograph of it to have a real picture of it.

I started by removing the plastic piece that holds the electrical lines that go over the engine:



There are 4 plastic (read: easily breakable) that hold the cover to the microfilter holder:



Carefully pry those open and remove the wrapped electrical line from inside. Make sure nothing is still connected to the microfilter holder since we will be removing this

Next, undo the three spring-load screw/clips from the top of the microfilter holder.



You can now pull that piece forward exposing the actual micro-filter:



Remove the micro-filter (and replace if needed)

Once the micro-filter is out of the way, 4 T30 Torx screws are exposed:



Unscrew all 4 and gently pull on the Micro-filter holder to remove from car (might take a little bit of prying and maneuvering to actually remove)

Location of all 4 screws:



Next Remove the PCV line by pushing on the clips (red arrows) and pulling off of the engine



Also remove the oil cap



With the 10mm socket, un-screw the 6 nuts holding the plastic engine cover (note: be careful not to drop any)

When you have removed all 6, this is what you should have:



Carefully remove the plastic engine cover and place it to the side

Replace the Oil Cap to stop any unwanted dust or dirt from getting into the engine (I also replaced the PCV fitting but didn't push it down all the way)

Next, carefully remove the spark-plug wire loom which is being held in place by two clips. Push the two clips together and put the wire loom to the side (do not completely unravel, this is simply gives you more space to work)



Picture of the clip:

__________________
-Josh
2004 Porsche GT3 - sold
2002 M3 Carbon Black - sold
2012 Ducati Streetfigher 848 - sold

Last edited by lax01; Wed, Feb-28-2007 at 02:19:08 PM.
Jump to top lax01 is offline   Reply With Quote
Sponsored Links
Register now and remove these ads
Old Wed, Feb-28-2007, 02:29:38 AM   #2
lax01
Registered User
 
lax01's Avatar
 
Join Date: Feb 2006
Age: 33
Posts: 2,719
Reputation: 0 lax01 will become famous soon enough
Location: Los Angeles, CA

United States




Default

Next, the removal of the coil pack and coil pack connection:




The top portion of the coil pack rotates up and allows you to unplug the coil pack connection from the actual coil pack. Un-plug the coil-pack and then simply use the top of the coil pack to expose the spark plug

Once you have removed the coil-pack, use the 3/8 drive wrench, the 3/8 drive extension(s) and the 5/8 spark-plug socket to remove the sparkplug:



The spark-plug is typically tight and takes a little bit of force to get moving. Put a little bit of leverage on it but do not strip the actual spark plug (bad). If you happen to strip the spark plug, take a sip of beer, re-assemble and take your car to a local mechanic

Finally locate your new spark plug. I use high-temp anti-seize on the threads to make sure I can safely remove them later.



Hand-screw the new spark-plug back in and then hand-tighten with your 3/8 ratchet



Finally torque to 22 ft/lbs with your torque wrench



Carefully re-seat the coil-pack on the spark-plug and then reconnect the cable:



Make sure the coil-pack is seated fully on the spark-plug

Repeat for the other 5 spark plugs

Complete the job by re-installing the plastic engine-cover and micro-filter holder in reverse order of above.

NOTE:

I noticed some oil in the spark-plug canal of the cylinder closest to the oil-fill cap (probably from spilling oil while filling).



I simply used a paper towel and long screw-driver to clean the walls before replacing the spark-plug.

After 58K miles, here are my spark plugs






If you have any questions please don't hesitate to ask.

-Josh (jbrozen (at) gmail.com)
__________________
-Josh
2004 Porsche GT3 - sold
2002 M3 Carbon Black - sold
2012 Ducati Streetfigher 848 - sold

Last edited by lax01; Wed, Feb-28-2007 at 02:39:14 AM.
Jump to top lax01 is offline   Reply With Quote
Old Thu, May-03-2007, 06:25:38 PM   #3
rneily
Registered User
 
Join Date: Oct 2003
Age: 44
Posts: 94
Reputation: 0 rneily has disabled reputation





Default

Quote:
Originally Posted by lax01 View Post
I noticed some oil in the spark-plug canal of the cylinder closest to the oil-fill cap (probably from spilling oil while filling).

This is most likely because the grommets around the spark plug tubes are not sealing correctly, and need to be replaced. There are 6 rings that go around each spark plug tube that keep the oil out of the spark plug area.
Jump to top rneily is offline   Reply With Quote
Old Thu, May-03-2007, 06:45:22 PM   #4
lax01
Registered User
 
lax01's Avatar
 
Join Date: Feb 2006
Age: 33
Posts: 2,719
Reputation: 0 lax01 will become famous soon enough
Location: Los Angeles, CA

United States




Default

I'll be sure to let the BMW Engineer who has my motor in Germany know

lol new motor = no care
__________________
-Josh
2004 Porsche GT3 - sold
2002 M3 Carbon Black - sold
2012 Ducati Streetfigher 848 - sold
Jump to top lax01 is offline   Reply With Quote
Old Mon, May-07-2007, 07:50:34 AM   #5
asaselzer
Registered User
 
asaselzer's Avatar
 
Join Date: Feb 2003
Posts: 232
Reputation: 0 asaselzer is on a distinguished road
Location: Fort Worth

United States




Default

damn, i have 78k on my engine! I wonder if they were replaced. time to go dig up the service receipts.
__________________
02 IR M3

08 JB M3 - ordered, June delivery!
Jump to top asaselzer is offline   Reply With Quote
Old Mon, May-07-2007, 08:19:29 AM   #6
asaselzer
Registered User
 
asaselzer's Avatar
 
Join Date: Feb 2003
Posts: 232
Reputation: 0 asaselzer is on a distinguished road
Location: Fort Worth

United States




Default

ahh yes. replaced at inspection II back at 49k miles
__________________
02 IR M3

08 JB M3 - ordered, June delivery!
Jump to top asaselzer is offline   Reply With Quote
Old Wed, Aug-13-2008, 08:43:35 PM   #7
RxTxK
Registered User
 
RxTxK's Avatar
 
Join Date: May 2007
Posts: 428
Reputation: 0 RxTxK is on a distinguished road
Location: Socal

United States




Default

Once again great DIY
Jump to top RxTxK is offline   Reply With Quote
Old Sat, Mar-28-2009, 08:21:39 AM   #8
Kriminol
KRIMINOL
 
Kriminol's Avatar
 
Join Date: Mar 2009
Posts: 6
Reputation: 0 Kriminol is on a distinguished road

United States




Default

I completely followed your steps and i got the job done easy! Now only if its ok with you. If you could please or anybody here be kind enough to do one DIY guide with pictures "BREAK PADS and ROTOR" replacement on a e46 M3.
Jump to top Kriminol is offline   Reply With Quote
Old Tue, Apr-21-2009, 06:51:29 PM   #9
ProjektONE
Milf Soup?
 
ProjektONE's Avatar
 
Join Date: Sep 2006
Posts: 1,053
Reputation: 0 ProjektONE is on a distinguished road
Location: Jacksonville, FL

Puerto Rico




Default

Quote:
Originally Posted by Kriminol View Post
I completely followed your steps and i got the job done easy! Now only if its ok with you. If you could please or anybody here be kind enough to do one DIY guide with pictures "BREAK PADS and ROTOR" replacement on a e46 M3.
Ill be doing this in the next week or so. Im going from OEM setup to StopTech Stage 2. Pad and rotor change is a straight through and easy process.

I used the spark plug DIY this weekend and all went well! The only trouble I had was removing the coils. I inserted a socket extension in the hole and moved the coil side to side till they came out. I took the time to wash all the misc covers that I removed prior to installing them again.
__________________
1996 ///M3 COSMOSSCHWARZ
Elitist Apparel
Jump to top ProjektONE is offline   Reply With Quote
Old Tue, Apr-21-2009, 07:37:57 PM   #10
Mash3
Look out below!
 
Join Date: Aug 2003
Age: 48
Posts: 7,315
Reputation: 0 Mash3 is a jewel in the rough
Location: Hollywierd

United States




Default

Quote:
Originally Posted by Kriminol View Post
I completely followed your steps and i got the job done easy! Now only if its ok with you. If you could please or anybody here be kind enough to do one DIY guide with pictures "BREAK PADS and ROTOR" replacement on a e46 M3.
There is a Sticky on the top of the page, titled: "DIY LINKS"

There, you will find what you need.

If you searched "Break Pads," you should get nothing, because there is no such thing as "break" pads.

Try "BRAKE Pads."

doh

.
__________________
http://www.m3forum.net/gallery/data/522/medium/Willow_.jpg
Forum Member Since 2003.
. . 2004 M3, SG/ IR. 95k miles. Original owner.
Jump to top Mash3 is offline   Reply With Quote
Reply

Bookmarks

Tags
diy, e46, pictures, sparkplugs

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY Spark Plugs? itsme E46 FAQ 6 Wed, Jun-28-2017 10:22:22 PM
I gave up any DIY for the spark plugs? Silver///M Faults, Fixes and DIY 2 Thu, Aug-25-2005 07:20:28 AM
spark plugs, how often? DIY? num3owner E36 M3 (1992-1999) 7 Fri, Nov-05-2004 01:42:30 AM
DIY on spark plugs? Drifter E36 M3 (1992-1999) 6 Thu, Sep-16-2004 03:53:51 PM
Spark Plugs - Definite DIY!! FLi GLi E36 M3 (1992-1999) 27 Sat, Apr-24-2004 02:05:49 PM



All times are GMT. The time now is 04:37:52 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
M3Forum.com and M3forum.net is in no way sponsored, endorsed or affiliated by or with BMW NA / BMW AG or any of it's subsidiaries or vendors.
BMW and M3 (E90 M3 | E92 M3 | E93 M3 | E46 M3 | E36 M3 | E30 M3) are registered trademarks of BMW AG.
M3Forum Terms of Service
Copyright 1999-2017 M3Forum.com
Discussing DIY: E46 M3 Spark-Plugs with Pictures in the Faults, Fixes and DIY Forum - Please share your experience and knowledge with other members by contributing your own DIY, or by helping another member find the elusive fix! at BMW M3 Forum.com (E30 M3 | E36 M3 | E46 M3 | E92 M3 | F80/X)