BMW M3 Forum
BMW M3 Forum BMW M3 Gallery BMW M3 Reviews BMW M3 Social Groups BMW M3 Chat M3Forum Sponsors >>
Loading


Mobile M3forum
Go Back   BMW M3 Forum.com (E30 M3 | E36 M3 | E46 M3 | E92 M3 | F80/X) > BMW M3 Discussions > E46 M3 (2001-2006)
Tire Rack Buy Winter Tires Now!
Not a member? Register Now!
Register Gallery All Albums Garage Search Today's Posts Mark Forums Read Calendar FAQ

E46 M3 (2001-2006) Engine: S54 - Max Hp: 333 hp at 7,900 rpm / 262 lb/ft at 4,900 rpm
Total Produced: 45,000+ - Years Produced: 2001 to 2006.


 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old Tue, Feb-27-2007, 06:59:04 AM   #1
bmwJohhnyD
user formerly known as bmwbob
 
bmwJohhnyD's Avatar
 
Join Date: Apr 2005
Age: 50
Posts: 13,436
Reputation: 0 bmwJohhnyD has disabled reputation
Location: New York #7/Fedic

United Nations




Default brembo bbk install

some interesting things on my 4 corner brembo bbk install today.

1. i did not need to trim the outer portion of the rear brake shield. some diy's from www.my330i.com and also the install pdf's and even the supplemental sheet from the brembo kit for the e46 m3 stated you had to trim about 1 inch from the rear dust shield all the way around the circumference, and then cut some more of it away to fit the caliper and the bracket. also it was stated that it was difficult to cut away the rear dust shield because it was thick. a good friend of mine did most of the work. all we had to do was cut about 1.5 inch triangle from where you mount the caliper, essentially to widen that space. and we cut them with regular tin snips. the rest was just simply bent out of the way and with this we had about an 1/8 to a quarter of an inch clearance all the way around the rotor and the caliper and the bracket...:nixweiss: i will let you know if sparks start coming from the car or it catches on fire.. so far on the drive home.. zero rubbing etc...

2. we did not cut the front triangle near the tie rod end from the front brake shield either.. we simply bent this out of the way and gained plenty of clearance... we even put the wheel bolts back in along with washers ( to substitute for the wheels) in order to ensure the rotors were completely mounted on the hub... so nothing was cut from the front rotor shield.. it was just slightly bent out of the way

3. regarding the rear stainless steel brake lines. the middle anchor point stock clip that holds the line away from the moving parts had to be 'tweaked' a bit to get that to fit tightly. we think it was due to the diameter of the goodridge anchor point included with the brakes being a bit smaller than stock

4. with regards to the rotor screws that mount the rotors to the hub.. for some reason we could use two screws [just like stock] on 3 of the 4 rotors. however, on the driver side we could only get one of the screws to actually hold the rotor because the 2nd hole was just a little two big [as a matter of fact the 2nd pre-drilled hole looked to be just like the pre-drilled holes for the rear rotor hats ] again i read in a couple of the diy's that you would only get to use one screw on each rotor. we think that if you had a rear rotor screw for that front hole that was too big that it would fit fine... we made sure that the rotors were lined up also. there is a distinct difference in the holes for the screws versus the holes for the dowels in the hub [screw holes are indented so screws sit flush]

5. we used an eye-ometer to measure the run-out on the rotors [since my dads meter did not work with teh magnetic base he bought] and decided it was well within the limits .. just make sure the rotors are mounted with a couple of lug bolts on them though.. or else they will look crazy out of round..

Last edited by bmwJohhnyD; Tue, Feb-27-2007 at 10:08:59 PM. Reason: clarification
Jump to top bmwJohhnyD is offline   Reply With Quote
Sponsored Links
Register now and remove these ads
 

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Brembo BBK Install Questions? phat///M3 E46 M3 (2001-2006) 2 Wed, Mar-12-2008 01:09:02 AM
Brembo BBK install @ BR Racing ///dean Member Photos and Videos 31 Tue, Sep-04-2007 06:31:46 AM
Brembo BBK Install ? hondas2000 E46 M3 (2001-2006) 6 Mon, Mar-26-2007 05:11:43 PM
brembo bbk install bmwJohhnyD E46 M3 (2001-2006) 14 Mon, Jan-22-2007 03:50:14 AM
brembo bbk install question daapower E46 M3 (2001-2006) 8 Mon, Jan-24-2005 06:13:06 PM



All times are GMT. The time now is 06:31:07 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
M3Forum.com and M3forum.net is in no way sponsored, endorsed or affiliated by or with BMW NA / BMW AG or any of it's subsidiaries or vendors.
BMW and M3 (E90 M3 | E92 M3 | E93 M3 | E46 M3 | E36 M3 | E30 M3) are registered trademarks of BMW AG.
M3Forum Terms of Service
Copyright 1999-2017 M3Forum.com
Discussing brembo bbk install in the E46 M3 (2001-2006) Forum - Engine: S54 - Max Hp: 333 hp at 7,900 rpm / 262 lb/ft at 4,900 rpm
Total Produced: 45,000+ - Years Produced: 2001 to 2006. at BMW M3 Forum.com (E30 M3 | E36 M3 | E46 M3 | E92 M3 | F80/X)